RH Limits – up to 95%

pH Limits 8.0-11.0

Description

EverStep’s Evertite is a next generation flooring adhesive for the most demanding of commercial installations. EverTite is a high-strength, high-tack adhesive for installing EverStep Cork and Dry Back LVP and LVT flooring over porous and nonporous substrates. EverTite offers extended open time, fast dry time and ease of application.
This unique adhesive has outstanding water resistance and tenacious bond strength for demanding installations such as hospitals, schools, nursing homes, hospitality, and food preparation centers. The low odor, Zero VOC formula is ideal for occupied buildings.

Preparation

The smoothness and cleanliness of concrete subfloors must meet or exceed the requirements of ASTM F710. Fill all holes and cracks with a latex fortified Portland cement based patching compound. EverStep only recommends the use of latex fortified Portland cement based products as a satisfactory patching or leveling compound. The floor should be flat 3/16” in a 10 foot span. The installation site must be acclimated with HVAC in operation. The installation site, as well as flooring materials and adhesive, must be maintained at 65°-85°F, and the humidity between 45-65% for 48 hours prior to, during, and continuously after the installation. Asphalt-based or cutback adhesive stains must be removed completely. Roll the
installation in both directions with a 75 lbs. 3-section roller immediately after flooring is placed and positioned, ensuring complete contact with adhesive. Read technical bulletin for floor preparation before using this product. This document may be obtained by calling EverStep Flooring at 844-296-4669.

Porous substrates

When installing LVP & LVT over a porous substrate, the adhesive should be allowed to dry to the touch sufficient to prevent slippage. Loss of adhesion can result if the flooring is not installed within the working time of the adhesive.

Non-porous substrates

Install LVP & LVT flooring into adhesive as it becomes dry to the touch with little or no transfer to finger. This will normally require 30 minutes of drying time at suggested installation temperature and humidity. Do not install flooring into wet adhesive on non-porous substrates.

Rubber & vinyl stair treads

Read Technical Bulletin titled Stair Tread and Riser Installation Instructions for complete instructions and limitations. This document may be obtained by calling EverStep Flooring at 844-296- 4669.
Note: Due to the many additives being used in or on concrete slabs, it is critical that a bond test be performed. Some treatments will repel any sealer or adhesive. If usage instructions are not completely followed, DO NOT USE THIS PRODUCT.

Recommended trowel and coverage

1/16” x 1/32”x 1/32” U-Notch (width, depth, spacing) for all installations. Coverage will be up to 220-260 sq. feet per gallon. Coverage is approximate and may vary depending on porosity of substrate and the angle at which the trowel is held.
IT IS THE INSTALLER’S RESPONSIBILITY TO APPLY THE PROPER AMOUNT OF ADHESIVE FOR THE JOB CONDITION WITH CLIP ON TROWEL PROVIDED.

Adhesive working time: Up to 4 hours after drying

Traffic

Follow EverStep’s installation guidelines; otherwise immediate occupation and use is permitted in dried adhesive installations. Allow at least five days following the installation before conducting wet cleaning procedures or initial maintenance.

Clean up

Use a clean wet cloth to clean up adhesive while still wet. Dried adhesive may require the use of an appropriate solvent.

Substrate conditions

Installations on or above grade over bare concrete substrates with up to 95% in-situ RH (per ASTM F2170), and a pH of 11.0.

Limitations

Not for outdoor use. Not for below grade installations. Store indoors at a temperature between 65-95°F. Cannot be used over substrates which have been chemically cleaned.
GHS Product identifier: Water-based adhesive

Precautionary statements

In case of eye contact, flush with water for 10-15 minutes. If irritation persists contact a physician. If prolonged skin contact causes irritation, wash with soap and water. If swallowed, consult a physician. Avoid release to the environment. Safety glasses and gloves are recommended if contact is expected. Dispose of in accordance with local, regional, national, international regulations as specified. Read SDS for detailed product information. SDS may be obtained by calling 844-296-4669.

Hazard statement

This material may cause slight irritation of the skin and eyes. May be an ingestion hazard. This product is not for human consumption. Use proper precautions.
Hazard symbol: None required Prop 65 statement: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other re-productive harm.

Supplemental information

Shelf Life: 1 year from date of manufacture in unopened, properly stored container. Avoid excessive heat or cold. Protect from freezing. Store indoors at a temperature of 65°-95°F. DOT Hazard Class: Unregulated.

LEED v4 Program Credits (where applicable)

• IEQ Credit 2.1, 2.2: Low Emitting Materials.
• VOC content is below that established by California SCAQMD Rule 1168.
• Compliant with CA Section 01350.